Your time:
Milan: 06:27 AM
LIVE CHAT
  Sale1 Sale2
Choose your language

Air heating batteries and control panels ATEX


Control-boxes-for-ATEX-duct-heaters_gen

The ATEX certified electric wiring heads are commonly used under limited pressure (less than 0.2 bar) and forced circulation.

They are made of heating elements (finned or non-finned) designed and designed to give rise to high performances and, at the same time, a high thermal exchange.

Temperature in Exit (of heat-treated air flow) and Surface Density (W / cm²), in addition to the type of fluid and the fluid velocity (air or gas) in meters per second (m / s) are the variables , together, determine the temperature of the elements installed on the battery board.

To ensure the suitability of these products to be installed in hazardous and explosive atmospheres, electrical wiring is housed and hermetically sealed inside a multiple enclosures of electrical wiring or tested for use in explosive atmospheres.

Explosion-proof ATEX electric batteries are commonly used under low-pressure (<0.2 bar) working conditions and forced circulation. The armored heating elements installed on board these special heaters are designed and positioned with a precise lay-out, so as to make the heat exchange optimal.

The skin temperature on the elements depends on the output temperature required by the specific application and the surface load (W / cm²) above, of course the type of fluid to be heated and its speed, measured in meters per second (m / s) or in kilograms per hour (Kg / h).

The head of the electrical wiring is the most stressed area of ​​the dangerous application to which these heaters are subjected. Each explosion-proof electric battery may have one or more certified ATEX headers and, therefore, suitable for use in explosive atmospheres.

We are able to produce CE-marked ATEX (certified explosion-proof Eex-de, Zone 1 and 2 – II2G / D ATEX) explosion-proof electric batteries, fully compliant with recent CEI and CENELEC standards.

This type of electric heaters is made of high quality materials such as carbon steel, stainless steel AISI-304, AISI-321, AISI-316 and Incoloy800 (heating element tube) and FeZn galvanized steel or AISI-304 stainless steel / 316 (limited to frame structure for the containment of elements and protection head for IP65-IP66 electrical contacts) and power supply inputs for power stages and thermoregulators (NPT or GAS type).

Typical Jobs

CERTIFIED QUALITY PRODUCT

The entire production cycle of ATEX heating electric batteries is subjected to stricter controls by the control bodies, which carry out predefined time cycles, strict controls in full compliance with ATEX regulations. In addition, this type of product is carefully tested for insulation resistance, dielectric rigidity, ohmic value and leakage current in the context of an ISO 9001: 2008 certified company organization and in full compliance with CEI / EN (EN60079-0:2012, EN60079-0:2012/A11:2013, EN60079-1:2007, EN60079-31:2015-05, ATEX 2014/34/UE and, where required, PED2014/68/UE).

TECHNICAL DATA

In designing this type of product, our technical office uses state-of-the-art computer programs to determine its dimensioning and thermodynamic performance calculators to optimize performance, taking into account the operating conditions of the battery itself.
Thanks to the constructive experience accumulated in 50 years of presence on the national and international market, in all major industrial sectors of the world economy, our technical and commercial office always provides the best technical and design solutions, customer specific application.
Already in the offer, we distinguish, compared to national and international competition, in providing all the technical details and results of thermodynamic calculation, which shows the correct size of the battery.

 

USEFUL DATA FOR DESIGN

The realization of an armored electric battery for air heating, whether it is made of finned or smooth heating elements, requires the knowledge of some technical data essential to its design:

  • FLUID TYPE: GAS or AIR
  • ATEX coding for WORKING ENVIRONMENT (internal or external use, in the presence of atmospheric agents). The part of the electrical wiring is housed inside standard carbon or stainless steel IP65 / IP66 stainless steel enclosures or headings, classified as ATEX E x-de IIB and IIC explosion proof headlamps for class temp. T1-T6 II2G-ATEX for use in explosive atmospheres (II2D Ex-tD A21 IP6X TX).
  • WORKING TEMPERATURE
  • LIGHT NET: Side D x C (Surface cm²)
  • AIR FLOW: Blown air by the fan used to cool the armored elements (m³ / h)
  • PROTECTION GRADE: IP65 or IP66 waterproof
  • STAGES: Partial total installed power
  • POWER VOLTAGE: Power supply voltage of the single-phase or three-phase battery and the type of voltage applied (Volts / 1Ph or Volts / 3Ph.)
  • NOMINAL POWER: Total power installed on board the armored electric battery (kW)
  • THERMAL OUTPUT: Differential between intake air temperature and output air temperature (Delta T in ° C)
  • LOAD LOSS: Differential pressure between inlet and air outlet (mm H2O)
ATEX Temp. Class
‘T6′: 85°C | ‘T5′: 100°C | ‘T4′: 135°C | ‘T3′: 200°C | ‘T2′: 300 | ‘T1′: 450°C
Cold zone Lg. A B A B A B A B A B A B
300 mm T6 X T4 X T3 X T3 X T2 X T2 X
250 mm T6 X T4 X T3 X T3 X T2 X T2 X
200 mm T6 X T4 X T3 X T3 X T2 X  
150 mm T6 X T4 X T3 X      
100 mm T6 X T4 X T3 X      
0 mm T6 X          
Working Temp. 0°C 100°C 150°C 200°C 250°C 300°C
Legenda:A = Temp. ClassB = Ex-proof head Temp.-proof allowance (X)= Yes ()= Not  

Batteria elettrica riscaldante ATEX IP65EXECUTION TYPE

Each electric heating battery is equipped with a safety (where required by the customer) that limits the sheath temperature in case of overheating of the surface temperature of the heating elements, which prevents damage to the heater or the installation on which it is installed. Depending on the type of process required, our technical office recommends the most appropriate thermocontroller (control thermostat, safety thermostat, thermocouple J or K or PT100 thermocouple). In addition, it is also possible to equip the electric heating battery with SCR or power thyristor device to be connected to control panel and control systems.

 
 
 
 
 

ATEX ELECTRICAL PANELS for the control of ATEX ELECTRICAL BATTERIES

On the customer’s specification and on the requirements of the plant on which the electric battery or the series of electric heating batteries of our production will be installed, we produce electric control panels ATEX in the presence of areas classified as Zone 2 and Zone 1, running EExp, with various functions for controlling our heaters. These frames are suitable for both indoor and outdoor installations; complete equipment in every detail and technical feature, both in terms of power control and process control.

The extensive experience gained in the electric heating sector has enabled us to design, create and optimize effective process control solutions in various application areas, as well as O & G in different countries, even outside the EU, and for installation in safe area, explosive atmosphere (Zone 2 and Zone 1), providing our customers with commissioning services through our highly specialized staff.

Here are some of the most important features that we can supply on our electric boards:

  • ATEX electrical boards of varying size depending on the control devices to be installed on board, also for remote control, suitable for indoor and outdoor use.
  • Frame-Waterproof Sealed Closure Seal made of Carbon Steel or Stainless Steel painted in RAL 7032 with IP 65 / IP66 protection rating for fixed or mobile, floor or wall installation.
  • Adjustment loop, even of “cascade-control”
  • Internal Diagnostics, Alarm Interface, Functional Alarms and Additional Alarms
  • Control panel with on / off switches and other fully wired commands, terminal blocks, etc.
  • Controlling external control via PLC / DCS; many of our applications are based on PLC control systems with DCS data exchange via fieldbus
  • Ventilation / Cooling System. On request, it is possible to equip the control cabinet with one or more additional cooling units and / or external heat sinks
  • Low load testing and output wave photography
  • Work Temperature Control Devices (Analog and Digital Thermometers)
  • Sizes of power from a few kW to several MWs (eg control panels for total power up to 5 or 6 megawatts), also composed of several modules connected in series
  • Voltages up to 690V
  • Power control delivered completely through SCR or mixed type

On request, it is also possible to equip the electrical cabinet of 6A 70V mono-phase analogue modulators with manual control built into IP56 enclosure or digital static relays with local control or remote control. These are mono-phase or tri-phase static power units (thyristors or SCRs), supplied with or without heat sink, in the 0-10V16A signal range, or up to 160A and 250A.
We are also able to provide SIL 2 and SIL3 applications on some control chains

SOME EXAMPLES: